search

BENDIX MC-30 TRAILER ABS CONTROLLER Anleitung zur Fehlerbehebung Seite 23

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 32
  • Inhaltsverzeichnis
  • FEHLERBEHEBUNG
    •
  • LESEZEICHEN
    • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 22
23
SECTION D - TROUBLESHOOTING THE ATC ACTIVE/WARNING LAMP
ATC Active/Warning lamp did
not illuminate during the EC-30
™
controller power-up sequence.
With ignition off, remove the 30-pin
connector from the EC-30
™
controller.
YES
NO
Turn ignition on and measure voltage
between pin C2 and ground (pins A1,
A2 or A3). Verify a measurement
equal to battery voltage. (About
12.0 VDC)
Check for corrosion or damage on
the 30-pin connector and wiring.
If none is found, replace the
EC-30
™
controller.
With a volt/ohm meter, check wiring,
ATC active/warning lamp and fuse.
When repair is made, reconnect
the 30-pin connector to the EC-30
™
controller and rerun the power-up
sequence. Go to Section A.
Note: If there is no wire in pin
C2 of the 30-pin connector, the
EC-30
™
controller is commanding
the ATC active/warning lamp, using
the J1939 serial communications
link.
In this confi guration, the actual ATC
lamp is driven by a vehicle dash
controller. Obtain the vehicle manual
and verify the wiring and function of
the ATC active/warning lamp.
To verify proper EC-30
™
controller
communication, go to Section K.
C2 ATC Active/Warning Lamp
A1,A2,A3 Ground
F2 ATC Enable/Disable Switch
1
2
3
K J H G F E D C B A
30-Pin Connector
See Note
this page
ATC active/warning lamp stays on
with no red LEDs on.
With a volt/ohm meter, check the
ATC active/warning lamp circuit
and the ATC enable/disable switch
wiring. Refer to fi gure 13. When
repair is made, reconnect the 30-pin
connector to the EC-30
™
controller
and rerun the power-up sequence.
If the condition still exists, replace
the EC-30
™
controller.
See Note
this page
Verify that the ATC enable/disable
switch is in the enable position.
If ATC active/warning lamp remains on,
turn ignition off and remove the 30-pin
connector from EC-30
™
controller.
Verify that the EC-30
™
controller is
configured for ATC by observing
the LEDs at power-up, blink code
diagnostics or using a diagnostic tool.
Seitenansicht 22
1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 31 32

Kommentare zu diesen Handbüchern

Keine Kommentare
Verwandte Produkte und Handbücher für Modulator BENDIX MC-30 TRAILER ABS CONTROLLER
Modulator BENDIX GEN 4 GEN 5 ABS Bedienungsanleitung   (10 Seiten)
Modulator BENDIX MC-30 TRAILER ABS CONTROLLER Bedienungsanleitung   (2 Seiten)
Modulator BENDIX MC-30 TRAILER ABS CONTROLLER Betriebsanweisung   (40 Seiten)
Modulator BENDIX TABS-6 TRAILER ABS MODULE Betriebsanweisung   (40 Seiten)
Modulator BENDIX MC-30 TRAILER ABS CONTROLLER Technical Information   (32 Seiten)
Modulator BENDIX GEN 4 GEN 5 ABS Betriebsanweisung   (24 Seiten)
Modulator BENDIX GEN 4 GEN 5 ABS Betriebsanweisung   (16 Seiten)
Modulator BENDIX M-21-M-22 ANTILOCK MOD ASSY Wartungshandbuch   (82 Seiten)
  • MCC Firenzi Oz-Post Dixie Chopper Woo-audio
  • Olympus Fernglas Philips Feuerschutz Quantum Audio Nein Magnavox CRT-Fernseher Rover Nein
  • Promate aidBar-2 HoMedics HL-200 Samsung S34E790C Honda HRB215 Electrolux ESF9423LMW
  • Sharkoon DarkGlider Bedienungsanleitung Humminbird ICE 55 Bedienungsanleitung Engl Raider 100 Bedienungsanleitung Denon AVR-3805S Betriebsanleitung Quantum LTO-2 Betriebsanweisung